A geyser is an essential appliance that is not just essential for the colder regions of the world but also for other parts. It fulfills the basic need of providing us with hot water, which can be used for multiple purposes such as bathing, washing clothes, washing utensils, cooking, and many other requirements.
But what happens when your geyser does not fulfill your basic requirements? Well, in such a case, you must try to find out the reason why your geyser is not working properly.
If you encounter any of these issues or any other problems with your geyser, it is advisable to seek a professional geyser repair service.
The Geyser Is Not Making The Water Hot
One of the most common situations you might face is no hot water coming out from the geyser. Given below are some reasons why your geyser might not be working properly.
- Inside the appliance, essentially, there are 2 heating elements. If there is no hot water from the geyser despite the power supply being OK at home, then this indicates that one or both heating elements may have failed.
- A faulty thermostat could be another reason for this. A thermostat is a device or part which helps you change or moderate the temperature of the water inside the geyser. If this part fails off position, then the water may not heat up at all. In both cases, you may need to contact a professional geyser repair service to resolve the issue or replace the part.
Water Coming Out Is Not Hot Enough
As mentioned previously, a thermostat controls the temperature of the water inside the geyser. In most geysers, the temperature that can be controlled is between 40 and 75 degrees Celsius. So if the setting of the thermostat is low, the power supply gets cut off at a low temperature, and the water will hence not get heated much.
Thus, the thermostat must be checked first if the water coming from the geyser is not hot enough. Also, in some cases, the thermostat may fault at a lower setting, which can also be responsible for water not being hot enough. In this situation, when the geyser is not heating water properly, you must get the thermostat checked.
It is better to contact a professional or electrician for the same since this issue can be more complicated than you imagine and may need professional hands, experience, and expertise.
Water Leaks
Faulty temperature and pressure (T&P) can cause water leaks. To check the T&P valve, place a bucket under the overhead pipe, open the valve, and flush it clear of detritus; if it still leaks, repair or replace it as required. Next, lower the thermostat setting to reduce excessive pressure or heat. After this, check for loose pipe connections; if you find any, then use a wrench to tighten it, and be careful not to over-tighten it.
Next, check the heating element bolts, and tighten them if required. Remove the heating element and replace the gasket if it is still leaking. Finally, look over if the storage tank is still leaking. Due to corrosion or other issues, such as bad o-rings, storage tanks can leak. Keep some extra o-rings handy from a supplier if you need to replace an o-ring.
Weird Noise Coming Out
Low, rumbling noise can indicate boiling water caused by overheating due to sediment build-up. Treat this by flushing the water from the geyser.
Build-ups of scales on electrical heating elements can cause a high-pitched, whining noise. To treat this, first, flush the water from the geyser. Afterward, clean the scales from the elements and the water heater tank. Eventually, install low-watt-density heating elements with a larger surface area for greater heat-transfer ability.
Odor Or Discoloration
Corrosion inside a glass-lined tank or a failing sacrificial anode rod can result in rust-colored water. If the anode rod fails, replace it with a magnesium anode rod.
A decomposing sacrificial anode rod can also unleash hydrogen, causing a smell like rotten eggs. To address this, first, flush the water from the geyser, then treat the tank and pipes for two hours with a solution of 2 pints of 3 percent hydrogen peroxide to 40 gallons of water.
Replace the failing anode with a zinc-alloy anode if the smell persists. If the smell still doesn’t disappear, replace the heater with a plastic-lined one.
Why Must You Look For the Best Geyser Repair Professionals?
Think again if you believe you don’t need a professional geyser repair service
Ask yourself a few simple questions. What happens when you have an emergency or the problem is too hard to handle? The truth is that you need a professional hand to do the repairs.
Professionals do thorough inspections and diagnostics of the situation. Always have the contacts of repairmen on your phone for emergencies. It helps save you from doing frantic searches when you need it the most. Below are the benefits of hiring a professional for your geyser repair service at home,
- No need to worry about emergencies
- Highly trained professionals
- Knowledgeable Experts
- Dealing with professionals is cost-effective
- Enhances your safety
- Guarantees you quality service
At The End
Geysers need to be maintained and checked regularly so that when you need hot water, especially in winter, you get the desired amount.
What is the point of getting this appliance installed in the first place if it is not working properly? There are many good electricians or professionals available who can check, install, repair, and replace geysers or their parts.
If your geyser does not heat water, you can contact Karsaaz for help and repairs or just simply download their app and avail offers and discounts. You can get a quick response and quick solution to all your geyser problems.
